电缆桥架的规格型号和型号规格应合乎当场工程施工环境艺术设计规定，查验內外应完好无缺，无缝拼接毛边，不可以发生弯折，折翘这些状况。 济南电缆桥架的安装使用要知道这8点！

The specifications, models, and specifications of the cable tray should comply with the artistic design requirements of the on-site engineering construction environment. The inside and outside should be inspected to ensure that they are intact, seamless splicing of burrs, and no bending or warping are allowed. Jinan cable bridge installation and use to know these 8 points!

1、电缆桥架的较大荷载和支撑点间隔应低于容许荷载和标准支撑点间隔，设备安装工程中不可载客，如当场自然环境的确需要时，需有安全防范措施设备即可载客，不可让不过关外行医生实际操作。

1. The large load and support point spacing of the cable bridge should be lower than the allowable load and standard support point spacing. During equipment installation engineering, it is not allowed to carry passengers. If the natural environment on the spot really requires, safety precautions should be taken to carry passengers. It is not allowed to let unqualified laymen operate.

2、再将表层处理过的立杆，托臂支撑架这些选用膨胀螺丝固定不动在墙壁上（得在混泥土构体和空心砖墙面，不可在空心墙），对当场电焊焊接处搞好防锈解决，当场开展刷涂反腐倡廉漆，电缆桥架敷设时，桥架中间的连接处支点尽可能设定在跨度的1/4上下处。

2. Then, use expansion screws to fix the surface treated upright poles and bracket support frames to the wall (only on concrete structures and hollow brick walls, not on hollow walls). Do a good job in preventing rust at the spot welding joints. Apply anti-corrosive and anti-corrosive paint on the spot. When laying cable bridge frames, the supporting points at the middle of the bridge connection should be set above and below 1/4 of the span as much as possible.

3、针对大跨度桥架较好是摆放在托架上连接，弯通或三通的地区则需独立提升支点，竖直方位的拖臂每隔1，5米长设一支撑点。

3. For large span bridges, it is better to place them on brackets for connection. For areas with curved or tee joints, it is necessary to independently lift the support points. For vertical trailing arms, support points are set every 1, 5 meters long.

4、桥架内的电缆运用卡带或是金属材料电缆卡扣开展固定不动，水准敷设安裝的电缆每隔2米做一个支撑点，竖直敷设安裝的电缆应每隔1-1，5米固定不动一次。

4. The cables in the bridge shall be fixed using a tape or metal material cable clip. For cables laid horizontally and installed, a support point shall be made every 2 meters, and for cables laid vertically and installed, it shall be fixed every 1-1 and 5 meters.

5、不允许穿过墙面及圈梁的桥架与孔眼一起堵死，如果是穿过服务器防火墙及防炎墙体时，应采用防火安全隔离措施。

5. It is not allowed to block bridges and eyelets that pass through walls and ring beams together. If they pass through server firewalls and anti inflammatory walls, fire safety isolation measures should be taken.

6、当工程施工自然环境在户外竖直安裝桥架时，避免过路人可以多手掀开桥架后盖板，订制桥架时要立即跟经销商反映，对桥架结构加固蝴蝶扣。

6. When installing the bridge vertically outdoors in the natural environment of the project construction, it is necessary to avoid passersby having to lift the rear cover plate of the bridge with multiple hands. When ordering the bridge, it is necessary to immediately report to the dealer and reinforce the butterfly buckle on the bridge structure.

7、当电力工程电缆和操纵电缆很少状况下，可敷设在同一条桥架上，选用隔开式桥架将不一样级别电缆分离敷设。

7. When there are few power engineering cables and control cables, they can be laid on the same bridge. Separate bridges are used to separate cables of different levels.

8、假如施工工地是高浸蚀自然环境规定，就可以选用不锈钢板，铝合金型材材料桥架。

8. If the construction site is subject to high erosion natural environment regulations, stainless steel plate and aluminum alloy profile materials can be selected for the bridge.

电缆桥架的安装使用要知道的事项要点已经为大家讲解完毕了，您对此有怎样的疑惑或者需求，就来我们网站 //www.comprepyme.com咨询了解吧！

The key points to know about the installation and use of cable trays have been explained to everyone. If you have any doubts or needs about this, please come to our website //www.comprepyme.com Consult and understand!