槽式电缆桥架是现代电缆防护设备中为常用的一种托盘结构桥架，槽式电缆桥架对于电缆传输完整信号和电缆分类管理都有很好的作用，槽式电缆桥架板材厚度在桥架相关相关标准例如JB/T 10216-2013中都有明确规定，不同材质、不同宽度的 济南电缆桥架的厚度是不同的。相关知识点整理如下：

Trough type cable tray is a kind of tray structure tray commonly used in modern cable protection equipment. Trough type cable tray plays a very good role in complete signal transmission and cable classification management. The thickness of trough type cable tray is clearly specified in relevant standards of cable tray, such as JB/T 10216-2013. The thickness of Jinan cable tray with different materials and different widths is different. Relevant knowledge points are summarized as follows:

槽式电缆桥架改向弯通包括：垂直左上弯通、垂直右上弯通、垂直左下弯通、垂直右下弯通、垂直左上三通、垂直右上三通等。托盘重量和盖板重量构成了槽式槽式电缆桥架的主要重量，例如普通镀锌槽式电缆桥架规格100*50mm规格，托盘每米重量为3.67千克，盖板每米的重量为2.20千克。

Channel type cable tray bend includes: vertical left upper bend, vertical right upper bend, vertical left lower bend, vertical right lower bend, vertical left upper tee, vertical right upper tee, etc. The weight of tray and cover plate constitute the main weight of trough type cable tray. For example, the size of ordinary galvanized trough type cable tray is 100 * 50mm, the weight of tray per meter is 3.67kg, and the weight of cover plate per meter is 2.20kg.

槽式电缆桥架吊架编写提料清单时应填写：名称+高度H+横担长度L，例如：角钢双拉吊架，规格H=1500mm，L=1000mm（角钢吊架默认横担长度=桥架宽度+200mm）。相关标准规定了槽式电缆桥架的耐火等级及其代号，耐火等级代号为N3，维持工作时间大于等于60分钟。

When preparing the material withdrawal list for trough type cable tray hangers, the following shall be filled in: name+height H+cross arm length L, for example: angle steel double pull hanger, specification H=1500mm, L=1000mm (default cross arm length of angle steel hanger=tray width+200mm). The relevant standards specify the fire resistance rating and its code of the trough type cable tray. The fire resistance rating code is N3, and the maintenance time is no less than 60 minutes.

电缆桥架的常见高度有50mm、100mm、150mm、200mm等。电缆桥架的常见宽度有100mm、200mm、300mm、400mm、500mm、600mm等。在电缆桥架需要分叉敷设或者向上、向下方向延展时，可以设置弯通，因空间条件限制或有特殊要求，可以使用铰连板。连接不同宽度或高度的两段电缆桥架时，可以使用变宽或变高连接板。

The common heights of cable tray are 50mm, 100mm, 150mm, 200mm, etc. The common width of cable tray is 100mm, 200mm, 300mm, 400mm, 500mm, 600mm, etc. When the cable tray needs to be bifurcated or extended upward or downward, a bend can be set. Because of space conditions or special requirements, hinged plates can be used. When connecting two cable trays of different widths or heights, you can use a widening or heightening connection plate.

按照标准，连接板的厚度应该与托盘和梯架的厚度保持一致，也可以选厚一个等级，盖板的厚度可以比桥架板材的厚度低一个等级。规格600x100桥架，按照QB/T 1453-2003标准，桥架厚度应为2.0mm，按照T/CECS 31-2017标准，桥架厚度应为3.0mm。

According to the standard, the thickness of the connecting plate should be consistent with the thickness of the tray and ladder, or a grade of thickness can be selected, and the thickness of the cover plate can be one grade lower than the thickness of the tray plate. The specification of 600x100 cable tray shall be 2.0mm according to QB/T 1453-2003 standard, and 3.0mm according to T/CECS 31-2017 standard.

槽式电缆桥架厚度高度等相关标准内容就讲解到这里了，您对此有什么信息就来我们网站 //www.comprepyme.com咨询吧！

The thickness and height of trough cable tray and other relevant standards will be explained here. If you have any information about this, please come to our website //www.comprepyme.com Consult!